# File generated by XConfigurator.

# **********************************************************************
# Refer to the XF86Config(4/5) man page for details about the format of 
# this file.
# **********************************************************************

# **********************************************************************
# Files section.  This allows default font and rgb paths to be set
# **********************************************************************

Section "Files"

# The location of the RGB database.  Note, this is the name of the
# file minus the extension (like ".txt" or ".db").  There is normally
# no need to change the default.

    RgbPath	"/usr/X11R6/lib/X11/rgb"

# Multiple FontPath entries are allowed (they are concatenated together)
# By default, Red Hat 6.0 and later now use a font server independent of
# the X server to render fonts.

    FontPath	"/usr/X11R6/lib/X11/fonts/TrueType"
    FontPath   "unix/:7100"

EndSection

# **********************************************************************
# Server flags section.
# **********************************************************************

Section "ServerFlags"

    # Uncomment this to cause a core dump at the spot where a signal is 
    # received.  This may leave the console in an unusable state, but may
    # provide a better stack trace in the core dump to aid in debugging
    #NoTrapSignals

    # Uncomment this to disable the <Crtl><Alt><BS> server abort sequence
    # This allows clients to receive this key event.
    #DontZap

    # Uncomment this to disable the <Crtl><Alt><KP_+>/<KP_-> mode switching
    # sequences.  This allows clients to receive these key events.
    #DontZoom

EndSection

# **********************************************************************
# Input devices
# **********************************************************************

# **********************************************************************
# Keyboard section
# **********************************************************************

Section "Keyboard"

    Protocol    "Standard"

    # when using XQUEUE, comment out the above line, and uncomment the
    # following line
    #Protocol   "Xqueue"

    AutoRepeat  500 5

    # Let the server do the NumLock processing.  This should only be 
    # required when using pre-R6 clients
    #ServerNumLock

    # Specify which keyboard LEDs can be user-controlled (eg, with xset(1))
    #Xleds      1 2 3

    #To set the LeftAlt to Meta, RightAlt key to ModeShift, 
    #RightCtl key to Compose, and ScrollLock key to ModeLock:

    LeftAlt        Meta
    RightAlt        Meta
   ScrollLock      Compose
   RightCtl        Control

# To disable the XKEYBOARD extension, uncomment XkbDisable.

#    XkbDisable

# To customise the XKB settings to suit your keyboard, modify the
# lines below (which are the defaults).  For example, for a non-U.S.
# keyboard, you will probably want to use:
#    XkbModel    "pc102"
# If you have a US Microsoft Natural keyboard, you can use:
#    XkbModel    "microsoft"
#
# Then to change the language, change the Layout setting.
# For example, a german layout can be obtained with:
#    XkbLayout   "de"
# or:
#    XkbLayout   "de"
#    XkbVariant  "nodeadkeys"
#
# If you'd like to switch the positions of your capslock and
# control keys, use:
#    XkbOptions  "ctrl:swapcaps"

# These are the default XKB settings for XFree86
#    XkbRules    "xfree86"
#    XkbModel    "pc101"
#    XkbLayout   "us"
#    XkbVariant  ""
#    XkbOptions  ""

   XkbKeycodes     "xfree86"
   XkbTypes        "default"
   XkbCompat       "default"
   XkbSymbols      "us(pc101)"
   XkbGeometry     "pc"
   XkbRules        "xfree86"
    XkbModel        "pc101"
    XkbLayout       "us"
EndSection

# **********************************************************************
# Pointer section
# **********************************************************************

Section "Pointer"
    Protocol    "PS/2"
    Device	"/dev/mouse"
    ZAxisMapping 4 5

# When using XQUEUE, comment out the above two lines, and uncomment
# the following line.

#    Protocol	"Xqueue"

# Baudrate and SampleRate are only for some Logitech mice

#    BaudRate	9600
#    SampleRate	150

# Emulate3Buttons is an option for 2-button Microsoft mice
# Emulate3Timeout is the timeout in milliseconds (default is 50ms)

    Emulate3Buttons
    Emulate3Timeout    50

# ChordMiddle is an option for some 3-button Logitech mice

#    ChordMiddle

EndSection

Section "Xinput"
    # PS/2 wheel Mouse
#    SubSection "Mouse"
#	DeviceName  "ps2Mouse"
# 	Protocol    "imps/2"
# 	Device      "/dev/psaux
# 	ZAxisMapping 4 5
# 	AlwaysCore
#    EndSubSection

     # For Logitech Trackman Wheel on USB
#    SubSection "Mouse"
#	DeviceName  "trwMouse"
#	Protocol    "imps/2"
#	Device      "/dev/input/mice"
# 	ZAxisMapping 4 5
#	AlwaysCore
#    EndSubSection

    # For Logitech Marble Mouse on USB
    SubSection "Mouse"
	DeviceName  "usbMouse"
	Protocol    "ps/2"
	Device      "/dev/input/mice"
	Emulate3Buttons
	Emulate3Timeout 50
	AlwaysCore
    EndSubSection
EndSection


# **********************************************************************
# Monitor section
# **********************************************************************

# Any number of monitor sections may be present

Section "Monitor"

    Identifier  "My Monitor"
    VendorName  "Unknown"
    ModelName   "Unknown"

# HorizSync is in kHz unless units are specified.
# HorizSync may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY.  REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.

    #HorizSync   31.5 - 48.5
    HorizSync   31.5 - 60

# VertRefresh is in Hz unless units are specified.
# VertRefresh may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY.  REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.

    VertRefresh 50-75

# Modes can be specified in two formats.  A compact one-line format, or
# a multi-line format.

# These two are equivalent

#    ModeLine "1024x768i" 45 1024 1048 1208 1264 768 776 784 817 Interlace

#    Mode "1024x768i"
#        DotClock	45
#        HTimings	1024 1048 1208 1264
#        VTimings	768 776 784 817
#        Flags		"Interlace"
#    EndMode

# This is a set of standard mode timings. Modes that are out of monitor spec
# are automatically deleted by the server (provided the HorizSync and
# VertRefresh lines are correct), so there's no immediate need to
# delete mode timings (unless particular mode timings don't work on your
# monitor). With these modes, the best standard mode that your monitor
# and video card can support for a given resolution is automatically
# used.

# 1024x768 @ 100Hz, 80.21 kHz hsync
Modeline "1024x768"   115.5  1024 1056 1248 1440  768  771  781  802 -HSync -VSync
# 1024x768 @ 30 Hz, 48.4 kHz hsync
Modeline "1024x768"    32.5  1024 1032 1176 1344   768  771  777  806 -hsync -vsync
# 1024x768 @ 60 Hz, 48.4 kHz hsync
Modeline "1024x768"    65    1024 1032 1176 1344   768  771  777  806 -hsync -vsync
# 1024x768 @ 70 Hz, 56.5 kHz hsync
Modeline "1024x768"    75    1024 1048 1184 1328   768  771  777  806 -hsync -vsync
# 1024x768 @ 76 Hz, 62.5 kHz hsync
#Modeline "1024x768"    85    1024 1032 1152 1360   768  784  787  823

EndSection


# **********************************************************************
# Graphics device section
# **********************************************************************

# Any number of graphics device sections may be present

Section "Device"
    Identifier        "Generic VGA"
    VendorName        "Unknown"
    BoardName "Unknown"
    Chipset   "generic"

#    VideoRam 256

#    Clocks   25.2 28.3

EndSection

# Device configured by Xconfigurator:

Section "Device"
    Identifier  "My Video Card"
    VendorName  "Acer"
    BoardName   "Trident"
    Chipset   "cyberblade"
    #VideoRam    4096
# Use Option "no_bitblt" if you have graphics problems. If that fails
# try Option "noaccel".
# Refer to /usr/X11R6/lib/doc/README.cirrus.
# To allow linear addressing, uncomment the Option line and the
# address that the card maps the framebuffer to.
    # Insert Clocks lines here if appropriate
EndSection


# **********************************************************************
# Screen sections
# **********************************************************************

# The Colour SVGA server

Section "Screen"
    Driver      "svga"
    # Use Device "Generic VGA" for Standard VGA 320x200x256
    #Device      "Generic VGA"
    Device      "My Video Card"
    Monitor     "My Monitor"
    DefaultColorDepth  32
    Subsection "Display"
        Depth       16
        Modes       "1024x768"
    EndSubsection
    Subsection "Display"
        Depth       24
        Modes       "1024x768"
    EndSubsection
    Subsection "Display"
        Depth       32
        Modes       "1024x768"
    EndSubsection
EndSection

# The 16-color VGA server

Section "Screen"
    Driver      "vga16"
    Device      "Generic VGA"
    Monitor     "My Monitor"
    Subsection "Display"
        Modes       "640x480" "800x600"
        ViewPort    0 0
    EndSubsection
EndSection

# The Mono server

Section "Screen"
    Driver      "vga2"
    Device      "Generic VGA"
    Monitor     "My Monitor"
    Subsection "Display"
        Modes       "640x480" "800x600"
        ViewPort    0 0
    EndSubsection
EndSection

# The accelerated servers (S3, Mach32, Mach8, 8514, P9000, AGX, W32, Mach64
# I128, and S3V)
Section "Screen"
    Driver      "accel"
    Device      "My Video Card"
    Monitor     "My Monitor"
    DefaultColorDepth   24
    Subsection "Display"
        Depth       24
        Modes       "640x480" "800x600" "1024x768"
        ViewPort    0 0
    EndSubsection
EndSection